Announcement

Collapse
No announcement yet.

Moving from Micro to Nitro

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Moving from Micro to Nitro

    For the past 7 months or so I have been flying a Microhelicopter (Feeda Dragonfly) and have within the last couple of weeks got myself a nice Shuttle Plus (And a big headache from the wife!). Any tips for the move upwards?
    -I don't crash, I just land with enthusiasm.

    A couple of 600n's with stuff on them that makes them fly..
    A 550 fbl with even more stuff on it to make it fly
    And a Mars 470 which needs stuff putting on it to make it fly

    And a DX8 too

  • #2
    just take your time, join a local club for advice and assistance and most importantly ENJOY YOURSELF

    Comment


    • #3
      Thanks

      Thanks. I know a couple of experienced flyers, one of which has set my baby up for me and made sure she was airworthy! to whom I am very grateful. I just wanted to sort of say hello to the community as I joined a while ago but didn't realy get involved. Thanks for the reply. (you can see a couple of pictures in the gallery, the album being My misses hates....)
      -I don't crash, I just land with enthusiasm.

      A couple of 600n's with stuff on them that makes them fly..
      A 550 fbl with even more stuff on it to make it fly
      And a Mars 470 which needs stuff putting on it to make it fly

      And a DX8 too

      Comment


      • #4
        Welcome Jamez

        I have found that having 1 or 2 mentors has helped me with tips/steps to complete the heli, and general advice.

        Invest in a sim (saves overall), and keep practising.

        The cost may keep you 'offside' with the missus, but if you are out of her hair for a few hours on the weekend I'm sure she won't mind.

        Comment


        • #5
          i to also fly micro helis...(nearly) and i also have an ic as well fot when i can fly a micro.......the rate im going that will be never...lol

          Comment


          • #6
            Rumour has it the micro is harder to fly than the IC but that has yet to be proven to me ( I think the IC is a MUCH more scary prospect just from size). My micro flying is just coming on enough to start side on hovering and a little bit of forward (the training gear came of at the start of the year and it looked tiny without that on!) but thanks all for the replies. Get stuck in with the Micro!!!!
            -I don't crash, I just land with enthusiasm.

            A couple of 600n's with stuff on them that makes them fly..
            A 550 fbl with even more stuff on it to make it fly
            And a Mars 470 which needs stuff putting on it to make it fly

            And a DX8 too

            Comment


            • #7
              The micro heli's, especially the fixed pitch ones, are definitely harder to fly that nitro models. You will find once you move onto the nitro models there is a major difference in the handling. I started with a hummingbird fp which was twitchy as hell, but cracked hovering and then progressed onto my hawk sport without using training legs.
              Ant
              Pilot of scale earth repelling objects

              Comment


              • #8
                Wind

                It was a bit windy on the first flight with my Shuttle, so not realyable to compare the 2 yet but will keep my progress posted, you are a brave man to fly the nitro without trainning gear, mine was and still is firmly attached!
                -I don't crash, I just land with enthusiasm.

                A couple of 600n's with stuff on them that makes them fly..
                A 550 fbl with even more stuff on it to make it fly
                And a Mars 470 which needs stuff putting on it to make it fly

                And a DX8 too

                Comment


                • #9
                  i cant even hover a micro yet let alone attempt tp fly a .50,i might be mad for buying it so soon but i just know its gonna come to that in the very near future.

                  Comment


                  • #10
                    I'm sure you will all find flying the larger IC helis much easier than the little micro electric ones.

                    The reason for this statement is that the IC models are all much bigger and therefore have more bulk, weight and a much larger rotor disk (the circle you can see when the blades are spinning) All these factors help the stability of the model emensely. The bulk and weight becuase there is far more presence in the air and therefore being far less likely to be affected by wind and the larger rotor disk to aid smoothness of hovering and control, so it will be far less twitchy than a micro electric model.

                    If you are having problems maintaining a smooth hover with the little electric models, it doesnt mean that you will have the same problems with the larger .30 and .50 size models, so don't be put off trying the larger ones just because you are having trouble with the little electric ones. My advice would just be to go for it and have fun

                    I hope this helps.


                    Cheers,


                    Pete.
                    Crashed and burned, or just got your fingers burnt???
                    Rise from the ashes with
                    Phoenix Model Aviation Ltd - For Flight training, Model setups & test flights and general advice just south of Bristol.

                    Comment


                    • #11
                      well that has persuaded me to try my .50 this weekend and see what i can do ,apart from crash that is.

                      Comment


                      • #12
                        Err, you'll need a tail rotor dude :P

                        Bought another Shuttle last night from Avicraft, that's 4 heli's now Oh, bought another Lama too but that's for a friend... 8O

                        Comment


                        • #13
                          do you fancy buying a lama for me.i will let you if you want.


                          and im gonna try and sort out the tail rotor this weekend as im off work next week so i will try and sort it and fire the baby up....do you think i will get it off the ground after seing what i can do with a micro heli? NO.

                          Comment


                          • #14
                            flying Sunday

                            Sunday looks good in this part of the world for Shuttle flying, will have to see how easy hovering is without too much wind (as it was blowy). As for getting the 50 off the ground, go for it..... whats the worst that can happen.
                            -I don't crash, I just land with enthusiasm.

                            A couple of 600n's with stuff on them that makes them fly..
                            A 550 fbl with even more stuff on it to make it fly
                            And a Mars 470 which needs stuff putting on it to make it fly

                            And a DX8 too

                            Comment


                            • #15
                              I flew (test flew) a mates piccolo a while back as he said I had more chance keeping it in 1 poece than him. I had been flying the Nexus for a while so did so. Very twitchy is my diagnosis. A Nitro heli is certainly far more stable and now having flown the Raptor 50, it would seem the bigger the better they fly.

                              Once you can sustain a stable hover and place the heli where you want I recommend you remove the training undercarriage as this will start to slow your progress. Just take it carefully as a Nitro heli is certainly far more dangerous than a lecky micro one.

                              Rob
                              Rob


                              T-Rex 450 Pro - BeastX v3 FBL, Hitec 5065's, DS520, Futaba R6203SB
                              Quad x-copter - KK 5.5 Multicopter v4.7, 850KVA motors, 30A ESC's, Orange RC FASST Rx, Carbon & Alu frame, LED strips for orientation, 10x4.5 props.
                              Quad x-copter - KK Plus 5.5d, 1000KVA motors, 30A ESC's, Orange RC FASST Rx, GF & Alu frame, LED strips, 10x4.5 props (coming soon!)
                              Futaba 9CP & 10CG

                              Comment

                              Working...
                              X