Rce G600

[MartinH]

hiya everyone, im fitting the rce-6600 gov to my 600 in the next few days, thanks to bladestriker for putting one up for sale, and would like a little help with it.
Just wondering if there are any finless bob videos on the setting up procedure, I think and I mean I think I caught a video a while back on it and cant find it now so if any one knows its location please let me kow
Or any helpful guide would be great.

[Nick B]

Is it os50,DX7? if so,Busterboy posted this for me

1. Install the governor per the manual. I'm using a DX7/AR7000 and the yellow sign wire is connected to AUX.

2. Set ATV for AUX2 to +100%/-100%

3. Set throttle curve to linear - 0-INH-50-INH-100

4. With the throttle stick on its lowest position, turn ON the radio.

5. Turn ON receiver and wait for the governor light to turn Green. When it's green, press the SET button on the governor for about 3 seconds until the GOV light starts to blink. Release the SET button then move the throttle stick to its highest position. The GOV light will turn OFF for a second then turn solid GREEN.

At this point, calibration is done. Verify that GOV is sensing the magnet by manually rotating the starter shaft with a 6MM allen wrence or just use your starter shaft. The lights on the GOV should turn OFF when one of the 2 magnets is directly under the sensor. (NOTE: only one of the two magnets should make the GOV light OFF. If you have both of the magnets turn OFF the GOV light, the magnets are installed incorrectly.)

PROGRAMMING THE DX7
1. Go to the master menu. (Press down+select and power ON)

2. Scroll to Input Selct menu and set AUX2 to INH

3. Turn OFF and the turn ON the radio again.

4. Go to the programming menu. (Press down+select)

5. Scroll to PROG.MIX1 menu. We are going to setup here the desired headspeed for Normal mode. Set it to make it look like this:

AUX2> AUX2 ON -- if this says OFF, your flight mode switch is not in normal
RATE: +80% --- for 1882 rpm headspeed
0%

SW: F-NR
OFFSET: 0

You set your RATE % based on the headspeed you want for normal mode. Refer to the table chart that came with the GOV.

6. Scroll to PROG.MIX2 menu. We are going to setup here the desired headspeed for IDLE1 mode. Set it to make it look like this:

AUX2>AUX2 ON -- if this says OFF, your flight mode switch is not in IDLE1
Rate +90% -- for 2024 rpm headspeed
0%
SW:F-S12
OFFSET: 0

Again, you set your RATE% based on the headspeed you want for IDLE1.

7. Scroll to PROG.MIX3 menu. We are going to setup here the desired headspeed for IDLE2 mode. Set it to make it look like this:

AUX2>AUX2 ON -- if this says OFF, your flight mode switch is not in IDLE2
RATE: +10% -- NOT 100% for 2171 rpm headspeed
0%
SW:F-S2
OFFSET: 0

NOTE: IDLE2 uses the base number from IDLE1 and add it's own value to it. So 90% (from IDLE1) + 10% = 100%

8. Exit programming menu and verify that when you flick the AUX2 switch on your radio, you can turn ON (green) or turn OFF (red) the governor. Take note which way your switch turns the GOV ON/OFF. If necessary, you can reverse AUX2 from the reversing sw. on the radio.

[MartinH]

Cheers Nick, think ive just found the exact responce on HF .

Was meant to delete this thread but cant now ahh well but yes it is the 0s50 and dx7 .

I'll try these settings first and if I have any problems im sure i'll post here

[lex7919]

If you cant get it to work as above try settin AUX2 AUX 2 in the Input select menu, mine does not work if you set it to INH !

[Supercaptaincrash]

what difference does it make to the earlier settings changing from aux2-inh to aux2-aux2 ?

[Eckchaz]

Sorry to Hi jack-ish Satch but Nick.. I used that same setting but i'm running a 55?

Is that gonna be to much for the 55? I dont have a tacho but I feel that on Idle 2 the engine seems to screem! So I've been sticking to Idle 1.. what was you using when u has the 55 on your LE?

[CookieMan]

Here's the Video linky Satch!

http://video.helifreak.com/?subpath=...e=aligngov.wmv