Solid G Reset?

[Tom Burgess]

How the hell do you reset these things to factory? I've made some edits to test the reset but it just isnt working for me??

[chugga-bug]

Press and hold both the 'L' & 'H' buttons while switching on RX.
This will reset the whole lot.

[Asid]

Either:

select a new heli

or

Hold down "L" & "H" buttons while switching on the receiver

Chugga beat me to it

[Tom Burgess]

Cheers guy's, however, I have tried the L and H buttons and everytime I go back in on the G view the settings have not defaulted back. ??

[Asid]

Select a new heli setup in the menu.

The L + H should work

[chugga-bug]

What settings are you expecting to change Tom, and to what?
There isn't a list of settings for each model memory in the manual, so unless you'd made a note of them, how would you know what 'Default' is?

[Tom Burgess]

What settings are you expecting to change Tom, and to what?
There isn't a list of settings for each model memory in the manual, so unless you'd made a note of them, how would you know what 'Default' is?

I'm expecting things that I went in and purposely changed to go to another value ie. their default value. I have messed so much with the other models that I really need to reset the whole thing.

[rspblake]

I. To Reset - Hold down both "L" and "H" buttons while
switching on the receiver...

This resets all models to default.

2. "Push and hold "P" about 6 seconds". The 6 seconds
does vary a little depending on the radio being used. It
could be as little as 5 seconds or as long as I 0 seconds.

3. When turning on the gyro, the LED turns green, wait 5
seconds for the gyro to initialize before moving the
helicopter, then LED turns off. If the LED stays on
Red, there is no TR signal. Check your radio and
installation.

4. The unit will exit a menu after about 30 seconds when
no buttons have been pushed.

http://www.rcheliaddict.co.uk/galler...LID_G_GYRO.PDF

[Tom Burgess]

Am i to take it that the setup consists of the following: (with a G-View)

Setup Menu = Set limits, direction and neutral

Model Menu = Choose a model?? I guess you choose a similar model and this loads a template of parameter's on the higher menu's of settings??

Pirouette Menu = Loaded from model selection above?

Response Menu = As Pirouette Menu?

Parameter Menu = As Pirouette Menu?

So, should a reset, reset all your limits and directions, along with all the menu items above the model select menu???

I hope they write a better manual for the Total G

[Tom Burgess]

I. To Reset - Hold down both "L" and "H" buttons while
switching on the receiver...

This resets all models to default.

2. "Push and hold "P" about 6 seconds". The 6 seconds
does vary a little depending on the radio being used. It
could be as little as 5 seconds or as long as I 0 seconds.

3. When turning on the gyro, the LED turns green, wait 5
seconds for the gyro to initialize before moving the
helicopter, then LED turns off. If the LED stays on
Red, there is no TR signal. Check your radio and
installation.

4. The unit will exit a menu after about 30 seconds when

straight from the manual!
no buttons have been pushed.

I have seen that Rob, and I am guessing that only point 1 refer's to the resetting of the gyro. The rest on that page is general information, pretty confusing if you ask me

[chugga-bug]

I've never actually tried to reset one Tom, but maybe try holding the buttons for longer when switching on? Let the gyro initialise fully before letting go? Only a guess mate. Like I say I've never done it myself.

[robgt]

It's pretty simple Tom

1. Remove Solid G.
2. Fit CSM 720

Cheers,
Rob

[chugga-bug]

I've got the manual in front of me Rob, and I can't find that bit anywhere!