Post what set up your gonna run E6/7

[Ross Northcott]

Just ordered a E6/7 and gonna run it as a E7, below is what iam gonna run what do you think?
My only concern is the motor, whether its the correct one?

Blades--- Radix Flybarless 690's & Rdaix 105 tails
Cyclic servo's--- JR DS8911 X 3
Tail servo--- JR DS8900G
FBL Controller--- Mini V-Bar v5.2
Speed controller---Kontronik Heli Jive 120HV with heatsink
Motor---Scorpian Motor 4525-520 Limited Edition
Batteries--- 12s 4500mah

What are your choices on your set up and views on the power set ups?

[chris jones2.4]

People have been using the hacker turnado in the e6

[Ross Northcott]

People have been using the hacker turnado in the e6

Problem is i already have this motor and not using it, so rather than it going to waste i thought i would try and use it.

[Jamin_00]

Think that motor not fit Ross but I'm not sure. Check on the freak as they were talking about this subject.

If I do order one I got all the gear on the bench.

Kontronik's esc and motor, bls servo all round, vbar mini or full depending on mounting locations and radix Fbl blades.

[Ross Northcott]

Think that motor not fit Ross but I'm not sure. Check on the freak as they were talking about this subject.

If I do order one I got all the gear on the bench.

Kontronik's esc and motor, bls servo all round, vbar mini or full depending on mounting locations and radix Fbl blades.

Ben when you say wont fit do you mean the size wont fit or the motor is to powerful?

[Jamin_00]

Size mate.

[Dudifiedad]

Run as an E7:

Outrage servos all round
Scorpion motor not sure which one yet
Kontronik esc or scorpion esc
Spinblades

[Mark E]

I recon the KV of that motor is to high for the stock pinions and do not think the 12 or 13 tooth ones are available yet, the hacker I think is being used is the A50-12L Turnado that is a 470Kv motor.

[Mark E]

If it does fit between the frames, but im not sure it will? with one of the upgrade pinions 12 or 13 tooth I recon you would be fine with that motor just put info into mr mels head speed calculator v3 and got this.

with 14 tooth pinion and jazz/jive esc programed in mode 4

65% throttle 2377 rpm
72% throttle 2521 rpm
85% throttle 2665 rpm

with 12 tooth pinion

65% 2037 rpm
75% 2521 rpm
85% 2665 rpm

this was if useing 35c lipos.

[Mark E]

Sorry ment on 12 tooth

65% 2037rpm
75% 2160rpm
85% 2284rpm

[Geek]

Think this is the link to the headspeed thing

http://rc.runryder.com/helicopter/ga...ript=headspeed

[Mark E]

Yes thats the one Paul, the synergy e6/7 main gear is already in the list of main gears.

[ROSSCO]

Currently flying pre-production kit:

Configuration: E6
FBL System: Futaba CGY750
Motor: Hacker Turnado 580kv
Pinion: 15T
Target Headspeed(s): 2000/2300
ESC: Castle Creations ICE2 HV120
Governor: Castle ICE
BEC: Flighttech 8a Regualtor @ 6V
RX Pack: Optipower 2150 2S 7.4V
Cyclic Servos: Futaba BLS451
Tail Servo: Futaba BLS251
Main Blades: Rail 606
Tail Blades: Rail 96
Lipos: 2x Optipower 5S 4300mAh (10S)