Announcement

Collapse
No announcement yet.

What have I done wrong??

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • What have I done wrong??

    Got my 700 e flying with an ALIGN BL700MX 510kv and a Castle Creations ice2 120HV, running the standard gearing with a 100% Idle up 2 curve. Using the Castle Creations link, it shows the max i can get is 2050 ish rpm. Heli sounds sluggish and not as I'd expect a 700 e to be like.

    Oh, by the way, I'm using Opti 5000mah lipos, they are on their second charge. Any thoughts??


    Thanks Arwel.
    ---------------------------------------------------
    Trex 700n DFC.
    Trex 700e TOP.
    Trex 700e Pro.
    Trex 600n DFC.

    Vbar Controller.

  • #2
    Not configured the throttle end points.
    x 3

    Comment


    • #3
      How do you do that??
      ---------------------------------------------------
      Trex 700n DFC.
      Trex 700e TOP.
      Trex 700e Pro.
      Trex 600n DFC.

      Vbar Controller.

      Comment


      • #4
        Yep Pauls right, you need to set a straight line 0-100 throttle curve in normal mode and redo the speed controller setup, so it can see your min and max throttle points, i had mine tach'd the other day at 2200 and still have more left if i need it
        James

        Sponsored by
        Align-Trex.co.uk
        Optifuel/optipower
        MKS servotech


        5 Eddie gold stars and christmas star

        Comment


        • #5
          Go to your throttle endpoints.

          Reduce them both to 50%, make sure you have a linear curve.

          Move your collective stick up to full positive, then turn on the Heli.

          You're now in programming mode.

          Increase the high end until the ESC plays a little tune.

          Go to low end with the stick, increase the endpoint value again until you hear the little tune.

          Governed, you will get a max of 2050rpm.
          x 3

          Comment


          • #6
            youtube Mr mel video castle throttle calibration
            Santander Factory Team

            Proud wearer of 5 x EGS

            Comment


            • #7
              As above,take blades off first too!.set +/-12 degrees of pitch.
              goblin BT700 havok (red)

              Comment


              • #8
                Guys,
                Just set up the end points as described and the ESC bleeps at high throttle 95% at the lowest it bleeps at 124% Is this ok?
                ---------------------------------------------------
                Trex 700n DFC.
                Trex 700e TOP.
                Trex 700e Pro.
                Trex 600n DFC.

                Vbar Controller.

                Comment


                • #9
                  Should I just run it on Fixed endpoints and taco it?
                  ---------------------------------------------------
                  Trex 700n DFC.
                  Trex 700e TOP.
                  Trex 700e Pro.
                  Trex 600n DFC.

                  Vbar Controller.

                  Comment


                  • #10
                    I would use gov then you have 3 headspead
                    Santander Factory Team

                    Proud wearer of 5 x EGS

                    Comment


                    • #11
                      Originally posted by GIXERMAN View Post
                      I would use gov then you have 3 headspead
                      But limited to 2050rpm?
                      ---------------------------------------------------
                      Trex 700n DFC.
                      Trex 700e TOP.
                      Trex 700e Pro.
                      Trex 600n DFC.

                      Vbar Controller.

                      Comment


                      • #12
                        Yes. The gearing limits you to 2050rpm, but it's fine.
                        x 3

                        Comment


                        • #13
                          Sacko,
                          So 2050rpm is my MAX with the stock setup? Should stick to Gov mode or get different pinion? What pinion would I need for 2150-2200rpm??

                          Thanks.
                          ---------------------------------------------------
                          Trex 700n DFC.
                          Trex 700e TOP.
                          Trex 700e Pro.
                          Trex 600n DFC.

                          Vbar Controller.

                          Comment


                          • #14
                            Originally posted by Arwel View Post
                            Guys,
                            Just set up the end points as described and the ESC bleeps at high throttle 95% at the lowest it bleeps at 124% Is this ok?
                            To add to Pauls very good post,it's recomended that when it plays the little tune you should go 2 or 3 more %.If you go back to do it then make sure you enable auto bail out first and then set the TH curve.
                            T- rex 600n V-bar
                            Logo 550sx V-bar
                            Logo 600sx V-bar
                            Logo 600sx V-bar night flyer

                            VBControl, but not the gay white version as i'm simply not gay enough to pull it off!

                            Comment


                            • #15
                              What does the auto bailout do?
                              ---------------------------------------------------
                              Trex 700n DFC.
                              Trex 700e TOP.
                              Trex 700e Pro.
                              Trex 600n DFC.

                              Vbar Controller.

                              Comment

                              Working...
                              X