Which motor to use with 35a align esc

[MarkG_R1]

Where can i find some ●Socket button head screw(M2.5X6mm)X2
●Washer(Φ2.6XΦ5.8X0.6mm)X2
To fix my motor? It didn't come with any

I've now ordered the correct pinion

[LaurenceGough]

Where can i find some ●Socket button head screw(M2.5X6mm)X2
●Washer(Φ2.6XΦ5.8X0.6mm)X2
To fix my motor? It didn't come with any

I've now ordered the correct pinion

Here you go:
Quick UK M2.5x6mm High Tensile Socket Cap Head Screws M2.5x6SC

Quick UK screws are really great quality too.

Don't forget medium strength Loctite!

[Andy from Sandy]

Where can i find some ●Socket button head screw(M2.5X6mm)X2
●Washer(Φ2.6XΦ5.8X0.6mm)X2
To fix my motor? It didn't come with any

I've now ordered the correct pinion

According to this link the motor is supplied with screws and washers

450MX Brushless Motor(3400KV) RCM-BL450MX HML45M01 - Electronics Motor - ALIGN-TREX.co.uk

If you purchased the motor brand new do not order them but call the supplier and ask them to send them. It might only be a few pence but most places are charging nearly £2.00 as the default postage. Allow them to rectify their shortcomings again if you purchased the motor brand new.

(I hope you didn't get short changed by the place I recommended)

[MarkG_R1]

According to this link the motor is supplied with screws and washers

450MX Brushless Motor(3400KV) RCM-BL450MX HML45M01 - Electronics Motor - ALIGN-TREX.co.uk

If you purchased the motor brand new do not order them but call the supplier and ask them to send them. It might only be a few pence but most places are charging nearly £2.00 as the default postage. Allow them to rectify their shortcomings again if you purchased the motor brand new.

(I hope you didn't get short changed by the place I recommended)

Hi Andy It wasn't the place you recommended i bought it from ebay as a new unused motor taken from a kit, my fault entirely
I've had several bits from Aligntrex.co.uk they've been great

[MarkG_R1]

Here you go:
Quick UK M2.5x6mm High Tensile Socket Cap Head Screws M2.5x6SC

Quick UK screws are really great quality too.

Don't forget medium strength Loctite!

Ordered: Thanks Laurence You're the fella from phoenix a week or so ago aren't you Awesome skills

I've probably got a lifetime supply of blue loctite

[MarkG_R1]

Guys what sort of headspeed and run time will i get with this setup?
Just as a guideline figure

Edit: forgot to mention i have three 3s Gens Ace 2200mah 40c lipo's

[Chris Boughton]

Guys what sort of headspeed and run time will i get with this setup?
Just as a guideline figure

Edit: forgot to mention i have three 3s Gens Ace 2200mah 40c lipo's

If you plan of 3d flying on a flat 100% throttle curve you will prob get 2:30-3mins
If you hover the whole flight on about 50% you prob get around 6-7 mins


I get 3 mins running at 3000rpm (100% thro) and the batt is at 25% left

[MarkG_R1]

Is 50% all that's required to hover?
It'll be a while before I'm doing any 3D
I was thinking of running about 75% flat on idle up for learning

[LaurenceGough]

I wouldn't quite use as low as 50%, maybe 60-70% but of course this depends on your gearing. A flat curve is best for the tail/ESC, just make sure you have soft start on. If it bogs a lot on pitch up then increase the throttle curve.

[Chris Boughton]

I wouldn't quite use as low as 50%, maybe 60-70% but of course this depends on your gearing. A flat curve is best for the tail/ESC, just make sure you have soft start on. If it bogs a lot on pitch up then increase the throttle curve.

Yer thats true i think my norm throttle curve is at about 65% which works really good