Announcement

Collapse
No announcement yet.

First Hover / Crash / what to check

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • First Hover / Crash / what to check

    HI all, just after some advice...finally braved the 1st outdoor attempt at a hover after 2 months sim training All went well & managed to get my blade 400 to hover about 1 ft above the ground as planned with minimal drift after a bit of trim (now I am totaly addicted).

    After a while of hover \take off \ landing practise a training skid got caught & caused a flip/crash.
    I would like to know what to check, as clearly the feathering shaft has bent (took it apart to see it was bent)after noticing the blades 'had drooped' & bad vibartion when powering up

    Obviously a good way to learn you way around the heli, but would appreciate any help on what else to check.

    thanks all
    Mark

    Blade MCX S300
    NEW - Gaui 200V2
    TREX 450se V2
    Blade 400 3D
    (Evil Chicken Killer with blood on her blades)

  • #2
    Good job with you're 1st hovering mate, sorry to hear about the bump. You'll be okay, we all crash.

    You should check you main shaft, your servos, main frame, linkages, tail boom, belt tension, swash mix and that all screws are tight. It's best to have a full overview of a heli after each flight, then test it slowly, be thorough as it can save your heli from any future accidents mate. And replace worn out / broken parts.

    Check your heli Before & After each flight. Hope this helps.
    ~JASON~
    HELI 1 : TREX 450 SE GF
    HELI 2 : PICOOZ HUGHES 500MD
    HELI 3: WALKERA 1#A
    HELI 4: WALKERA CB100
    SIM : AEROFLY PRO DELUXE
    sigpic

    Comment


    • #3
      I did expect a crash, but what an addiction with the 1st hover!! thanks for the advice, cant wait for hover 2.....more sim time now
      Mark

      Blade MCX S300
      NEW - Gaui 200V2
      TREX 450se V2
      Blade 400 3D
      (Evil Chicken Killer with blood on her blades)

      Comment


      • #4
        good going on your first outside flight did you have any practise inside?
        Blade 400 spextrum dx6i

        Comment


        • #5
          not really, but my inlaw has a decent size garden and it never really gets windy as its surrounded by trees, perfect for the first few attempts to get up in the air - thats all I was doing after 2 months of practise on Pheonix, I started with a few ups & downs in the air to get the trim right etc & a few 'slam downs' on the training gear, but i was 'sort of hovering' drifting around a bit , perhaps 8ft diameter if you drew a circle, then gradually got it down to about 1 ft diameter 'drift' -so was quite happy for a 1st few attempts - mainly getting used to the sensitivity of the blade.(I used the seetings from this site for the DX6i, which are perfect & do seem to calm down the sensitivity of the blade).

          I was at another lift off that the training gear snagged on something & she flipped over.
          Had a quick look & you could see the rotors were 'drooping', so a quick isnspection revealed the feather shaft was bent. Clearly designed to do this on impact to protect the heli I would imagine.


          I am looking for local flyers in Portsmouth to meet up with,get advice etc etc.
          But its always good to learn through doing it yourself, with expert advice to guide you..

          Just such an addictive hobby!! Its the sound that gets me when they power up!!!
          Mark

          Blade MCX S300
          NEW - Gaui 200V2
          TREX 450se V2
          Blade 400 3D
          (Evil Chicken Killer with blood on her blades)

          Comment


          • #6
            Congrats on your first hover, i did mine yesterday for a full pack so i know the feeling your on about
            Nik.

            Before you ask:

            About 2 miles
            Over £500
            Very difficult
            Over 80mph
            NO, you can't have a go



            Don't forget the 'Search' and 'Thanks' buttons.

            RIP Anthony 'Tinny' Lombardi (25195517)

            Comment


            • #7
              I attempted my first hover with my Twister 3D Storm (Blade 400) yesterday and it didnt go too well..It needs more setting up to stop it leaning over once it has spooled up. Also I need to sort the TX out and do a bit more practise and reading. Congrats on your first hover though

              Comment


              • #8
                I love the sound mine makes as it spools up! But not the sound it makes when it hits something...

                Anyway, one site which has taught me how to repair my blade is:
                http://www.repairblade400.com/

                One good tip is to take some pictures of the head setup before disassembling, because its really easyu to forget which way round something goes, or which rod connects to which bit!

                Things that went on mine when I crashed were:
                feathering spindle,
                main shaft (also bends really easily),
                main gear (if the blades stopped too suddenly, one of the teeth could have stripped),
                servo gears (you only fell from a short height, so prob. wont be a problem)
                but dont forget to check other stuff, like the main blades want to be still in one peice - you can check that they both flex correctly.

                best of luck with the repair - and just remember, if you have any questions, you can always ask the people on here! They have all been great at helping me!
                Blade 400 3D; stock
                9 flights since last crash

                Blade MCX; modified swash
                For those rainy days...

                Comment


                • #9
                  if its leaning over just trim it up or if you have to adjust your linkage, but even when you have this down it will still lean to one side because of the rotors spinning
                  Nik.

                  Before you ask:

                  About 2 miles
                  Over £500
                  Very difficult
                  Over 80mph
                  NO, you can't have a go



                  Don't forget the 'Search' and 'Thanks' buttons.

                  RIP Anthony 'Tinny' Lombardi (25195517)

                  Comment

                  Working...
                  X