|
|
| Register | FAQ | Calendar | Store | Mark Forums Read |
|
|
#1 (permalink) |
|
Site Sponsor
![]() Join Date: Apr 2008
Location: Yiewsley
Posts: 1,911
Thanks: 277
Thanked 279 Times in 264 Posts
![]() ![]() ![]() |
Does anyone know how I can asign small amount of throttle to aile & elev with the DX7 that if it can be done with the DX7 I dont want to up the throttle pitch as I've got it set just right so all my heli's have the same feel to them with exception to my Trex 600 nsp I need more power when giving large amounts of aile/elev.
__________________
Today's outlook is fine for flying.
|
|
|
|
|
|
#2 (permalink) | |
|
Proud Site Sponsor
![]() Join Date: Oct 2007
Location: Blaby, Leicester
Posts: 1,970
Blog Entries: 2
Thanks: 191
Thanked 320 Times in 255 Posts
![]() ![]() ![]() |
Quote:
Yup, Pretty Much can do that, its called mixing.. in the prog mix menus and you have 3 that you can set upI had a mix set up where i imput rudder it increases the throttle a bit to cure the bog that extreme piroing can do ![]() Simply Browse trough the menus till you see Prog Mix 1 or something like that, then you select Aile > Throttle then the Precentage you want the throttle to increase, do this for the others, but with Elev > Throttle ![]() I think you can assign a switch aswell, not too sure though Hope this Helps
__________________
Vision50 Competition -- Orgasmic! Trex600NP -- Niiice!! BlademCX -- Bordem Saver! BeltCP -- Crashed CopterX450-- Very Fast! I am piro whore! Proud Owner of 2 Eddie Goldstars Last edited by callum; 28-06-2009 at 07:13 PM. |
|
|
|
|
| The Following User Says Thank You to callum For This Useful Post: | tourerjim (28-06-2009) |
|
|
#3 (permalink) |
|
Registered Member
Join Date: Oct 2008
Location: UK
Posts: 520
Thanks: 117
Thanked 148 Times in 127 Posts
![]() ![]() |
Hi
Use one of the MIX CHANELS. mix the chanel you want i.e. ail to throttle. Around 20% is a good figure. Make sure that the throttle high point is about 90%. Check for overdriving of the throttle servo. There is a + and - figure if you are not sure wich value to set look at the throttle servo while moving the chanel you mixed it to. This can be tied into the flight mode switch. This is how i understand it.
|
|
|
|
| The Following User Says Thank You to Asid For This Useful Post: | tourerjim (28-06-2009) |
|
|
#4 (permalink) | |
|
Site Sponsor
![]() Join Date: Apr 2008
Location: Yiewsley
Posts: 1,911
Thanks: 277
Thanked 279 Times in 264 Posts
![]() ![]() ![]() |
Quote:
__________________
Today's outlook is fine for flying.
|
|
|
|
|
|
|
#5 (permalink) |
|
Site Sponsor
![]() Join Date: Apr 2008
Location: Yiewsley
Posts: 1,911
Thanks: 277
Thanked 279 Times in 264 Posts
![]() ![]() ![]() |
Am I doing something wrong cant seem to get the throttle to work with aile/elev so it anyone has the DX7 & can advise I'd be greatful.
__________________
Today's outlook is fine for flying.
|
|
|
|
|
|
#6 (permalink) |
|
Registered Member
Join Date: Mar 2008
Location: London
Posts: 767
Thanks: 35
Thanked 115 Times in 108 Posts
![]() ![]() |
I've done it before using the programable mixes on my DX7 so it's definitely possible. I don't have my DX7 here right now though so I can't give you detailed info on how it's done but Callum's post above sums it up pretty well I'd say.
Last edited by J-S-Q; 29-06-2009 at 02:41 PM. |
|
|
|
| The Following User Says Thank You to J-S-Q For This Useful Post: | tourerjim (30-06-2009) |
|
|
#7 (permalink) |
|
Registered Member
Join Date: Oct 2008
Location: UK
Posts: 520
Thanks: 117
Thanked 148 Times in 127 Posts
![]() ![]() |
Hi
Make sure you set it up as cyclic to throttle mix and not the other way round. First of all: Enable P-Mix1 Set aileron as master and throttle as the slave Rate + (15 to 20%) - (15 to 20%) (use servo mon to check correct direction) Switch position to On Offset to 0 Enable P-Mix2 Set Elevator as master and throttle as the slave Rate + (15 to 20%) - (15 to 20%) (use servo mon to check correct direction) Switch position to On Offset to 0 If you set your max Throttle point to 90% not 100% it will help avoid throttle binding at high throttle values Sub trim can be used to stop the throttle servo binding. Use servo montor function to see it working. This is my understanding of it
|
|
|
|
| The Following User Says Thank You to Asid For This Useful Post: | tourerjim (30-06-2009) |
|
|
#8 (permalink) | |
|
Site Sponsor
![]() Join Date: Apr 2008
Location: Yiewsley
Posts: 1,911
Thanks: 277
Thanked 279 Times in 264 Posts
![]() ![]() ![]() |
Quote:
__________________
Today's outlook is fine for flying.
|
|
|
|
|
|
|
#9 (permalink) |
|
Site Sponsor
![]() Join Date: Apr 2008
Location: Yiewsley
Posts: 1,911
Thanks: 277
Thanked 279 Times in 264 Posts
![]() ![]() ![]() |
Corrrr! what a differents asigning thottle to elev & aile, gives you so much more control effortlessly.
__________________
Today's outlook is fine for flying.
|
|
|
|
![]() |
|
|
|
|
| Thread Tools | |
| Display Modes | |
|
|