Tweet
I've never had an ESC that needed things to be setup on it for it to work, so i need a little help getting the settings correct on this ESC.
Here is the list of settings/options:
• Active free-wheeling circuit mode: Freew. off/Freew. on
• Govenor mode: Gov. off/Gov. store/Gov./fast Gov.
• Govenor mode P-gain: 0.7/0.9/1.2/1.4/1.6/1.9
• Govenor mode I-gain: 0.02/0.03/0.05/0.06/0.08/0.09
• Startup speed: Heli slow/Heli middle/Heli fast/Plane slow/Plane middle/Plane fast
• PWM frequency: 8kHz/9kHz/10kHz/12kHz/14kHz/16kHz
• Start-up power: Auto 1~32%/2%/4%/8%/16%/32%
• Motor timing: 0°/6°/12°/18°/24°/30°
• Brake: off/Acro/Acro hard/smooth/middle/hard
• Cut-off type: off/slow down/cut-off/NiMh/LiFe/LiPo
• Cut-off voltage (LiFe mode): 2.2/2.3/2.4/2.5/2.6/2.7
• Cut-off voltage (LiPo mode): 2.9/3.0/3.1/3.2/3.3/3.4
• Cells: 4/5/6/7/8/9
• Cells: 10/11/12/13/14/15
• Special functions: Beep short/Rev./Stop/Full speed/F3A brake/Auto timing
Mostly i have no idea what to set these to so it will work. Could someone give me some assistance on where to start?
This will be going on a 550 with 600M motor.
Here is my best guess at some settings:
• Active free-wheeling circuit mode: Freew. on
• Govenor mode: Gov. off
• Govenor mode P-gain: N/A
• Govenor mode I-gain: N/A
• Startup speed: Heli middle
• PWM frequency: 8kHz
• Start-up power: Auto 1~32%
• Motor timing: 0°
• Brake: off
• Cut-off type: slow down
• Cut-off voltage (LiFe mode): N/A
• Cut-off voltage (LiPo mode): 3.2
• Cells: 6
• Cells: --------
• Special functions: Beep short/Rev./Stop/Full speed/F3A brake/Auto timing - No idea?
Ryan
Here is the list of settings/options:
• Active free-wheeling circuit mode: Freew. off/Freew. on
• Govenor mode: Gov. off/Gov. store/Gov./fast Gov.
• Govenor mode P-gain: 0.7/0.9/1.2/1.4/1.6/1.9
• Govenor mode I-gain: 0.02/0.03/0.05/0.06/0.08/0.09
• Startup speed: Heli slow/Heli middle/Heli fast/Plane slow/Plane middle/Plane fast
• PWM frequency: 8kHz/9kHz/10kHz/12kHz/14kHz/16kHz
• Start-up power: Auto 1~32%/2%/4%/8%/16%/32%
• Motor timing: 0°/6°/12°/18°/24°/30°
• Brake: off/Acro/Acro hard/smooth/middle/hard
• Cut-off type: off/slow down/cut-off/NiMh/LiFe/LiPo
• Cut-off voltage (LiFe mode): 2.2/2.3/2.4/2.5/2.6/2.7
• Cut-off voltage (LiPo mode): 2.9/3.0/3.1/3.2/3.3/3.4
• Cells: 4/5/6/7/8/9
• Cells: 10/11/12/13/14/15
• Special functions: Beep short/Rev./Stop/Full speed/F3A brake/Auto timing
Mostly i have no idea what to set these to so it will work. Could someone give me some assistance on where to start?
This will be going on a 550 with 600M motor.
Here is my best guess at some settings:
• Active free-wheeling circuit mode: Freew. on
• Govenor mode: Gov. off
• Govenor mode P-gain: N/A
• Govenor mode I-gain: N/A
• Startup speed: Heli middle
• PWM frequency: 8kHz
• Start-up power: Auto 1~32%
• Motor timing: 0°
• Brake: off
• Cut-off type: slow down
• Cut-off voltage (LiFe mode): N/A
• Cut-off voltage (LiPo mode): 3.2
• Cells: 6
• Cells: --------
• Special functions: Beep short/Rev./Stop/Full speed/F3A brake/Auto timing - No idea?
Ryan
Comment