Announcement

Collapse
No announcement yet.

Total G govenor set up DSX 9

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
  • #1

    Total G govenor set up DSX 9

    Hi all
    Setting up TotalVibe, my Flybarless Vibe 50, and I am struggling to set up a mix for the Gov.

    I want to set up a mix so that I have two headspeeds opperated by my idle up switch on my DSX9 MK1.

    It's mega complicated or I have missed somthing

    I have my flybarless flight modes set to my aux 4 Channel which is then set in the device mix part of my tx to the Aux 2 switch to give me 2 flight gains and an off position which I can adjust via the travel adjust on the Aux 4 ta limits.

    My Aux 2 switch is set to flight mode switch and the Total G menu for the govenor is set to Aux 2 .

    The flight mode or gian for the Total G is set to Aux 4 and that works ok.

    Now this should work but No when I look at the monitor on the TX the flight mode switch does nothing to the Aux 2 position , but the aux 4 (rudder DR) switch does switch the aux 2 monitor.

    Help I am very confused.

    I have noticed under the Device menue section for the Aux 2 section it says Inh is this relevent ???????

    I have looked on heli freak but they just go on about electrics.humm

    anyone ??????

    My head hurts soooooooo much.

    Thanks x Rachel
    Tags: None
  • #2
    Act

    Good Mornimg Rachel,
    Yes turn the INH to Act and that should sovel your problems,just looked at mypcm9X.
    Good Flying,
    Marty.
    Chase 360 and JR Ninja all controlled by JR XG8


    proud owner of 2 EGS's

    Comment

    • #3
      I use Futaba gear and if it says INH then it means the function isn't active. I'd change that so that the function is active and see what happens.

      I'll be interested to see how you get on with the TotalG governor, the one on my Rave seems to keep the headspeed reasonably well but when reach the top of a climbout, and the head unloads, then it seems to close the throttle too much and then hunts for a bit trying to get the headspeed back up.

      Comment

      • #4
        Hi Rachel dont we JR9 owners use the gear function for governor and AUX 2 for gyro sense..
        Heli central...Basildon RC helis...strictly helis only...




        Comment

        • #5
          Ok sort of got it worked out now Pulsar has sorted it (my hero)
          He has also set up a cunning mis so that it works in Idle up 1 & 2 but not normal mode.

          One question ????????????

          On the Total G screen , dose the RMP shown equal headspeed or engine speed ??????????? My guess is its headspeen but even the detailed instructions are vague

          I will do a long and full post tonight so we will all know how to do it in future.

          Hugs X rachel

          Comment

          • #6
            sounds like a nightmare to set up the gov on the total g
            Kel Velocity 50 sk-720 ,Fusion 50 v-bar pro 5.2 ,Velocity 90 v-bar pro 5.2 & JR DSX11 ,Phoenix and a fridge full of bottled water RCHA Courier Services PM for Details www.parcelshipper.co.uk and www.impactexpress.co.uk

            Comment

            • #7
              The RPM shows the headspeed that you'd like to have, so in my case I've got that set to 1950 in idle up.

              What you also need to set is the Gear Ratio. What you set this to depends on where you've got the sensor installed, if it's on the backplate like mine, the fan or the clutch then it'll be the main gear to pinion ratio, i.e. main gear teeth / pinion, so for my Rave that's 130 / 16 = 8.125 : 1. As the Gear Ratio setting is x10 then mine is set to 81. If you've got the sensor on the main gear then the ratio is 1:1 so the Gear Ratio would be set to 10.

              Hope this makes sense.

              Comment

              • #8
                Originally posted by millerman View Post
                sounds like a nightmare to set up the gov on the total g
                Actually its not
                I am just a brain donor

                The mixes we have now used are so I can have my govenor coming on automaticaly with my idle up switch & its the same mix I use for my CSM revlock 20.

                More later
                X rach

                Comment

                • #9
                  Originally posted by millerman View Post
                  sounds like a nightmare to set up the gov on the total g
                  It's harder to setup the TotalG governor than an align governor, although you do need a tacho to set the align governor, but I found it no more difficult setting up the TotalG than setting up my Multigov as the principle is the same.

                  Comment

                  Previous template Next
                  Working...
                  X