avant dampeners?
Iam looking to put some slightly softer damperners in my aurora and need to know the best ones, does anyone know what Durometer is standard?
i have been looking at either the 70 or 80.
Thx Ross
SWRCH
Synergy E5 FBL, V-bar 5.2, Kontronik 120hv helijive,HKIII scorpion motor, BLS 351, BLS 251.
Synergy E7 FBL V-bar 5.2, knotronik 120hv helijive, pyro 450kv motor, bls251, bls351.
Mikado logo 500se/sx FBL V-bar 5.2, kontronic 80hv,bls351,bls251, scorpian motor.
Mikado logo 600/SX FBL V-bar 5.2, kontronic 80hv ,bls451,bls251scorpian motor.
Alees Rush 750 FBL, V-bar silverline 5.3, kosmik 160hv, scorpion motor, outrage servo's
Henseleit TDR FBL,V-bar silverline 5.3 kontronik 120hv helijive, pyro 520kv motor, bls 253, bls 251.
Diablo FBL, V-Bar Silverline 5.3, Kosmik 160hv, Scorpion Ultimate Motor, Outrage Servo's
Gaui X5 FBL v-bar mni, 5.3 Kontronik 120hv, scorpion motor, gaui servo's
Spektrum DX18 QQ
anyone?
Thx Ross
SWRCH
Synergy E5 FBL, V-bar 5.2, Kontronik 120hv helijive,HKIII scorpion motor, BLS 351, BLS 251.
Synergy E7 FBL V-bar 5.2, knotronik 120hv helijive, pyro 450kv motor, bls251, bls351.
Mikado logo 500se/sx FBL V-bar 5.2, kontronic 80hv,bls351,bls251, scorpian motor.
Mikado logo 600/SX FBL V-bar 5.2, kontronic 80hv ,bls451,bls251scorpian motor.
Alees Rush 750 FBL, V-bar silverline 5.3, kosmik 160hv, scorpion motor, outrage servo's
Henseleit TDR FBL,V-bar silverline 5.3 kontronik 120hv helijive, pyro 520kv motor, bls 253, bls 251.
Diablo FBL, V-Bar Silverline 5.3, Kosmik 160hv, Scorpion Ultimate Motor, Outrage Servo's
Gaui X5 FBL v-bar mni, 5.3 Kontronik 120hv, scorpion motor, gaui servo's
Spektrum DX18 QQ
Ross,
I am sure robgt will know the answer - maybe you should send him a PMOtherwise, post your question on the Avant support forum - you will get an answer very quickly there from Avant or Augusto himself
Avant RC Support Forums
Proud Sponsor/Pitman/Servant/Slave to Bart101s fleet of Outrage and Avant helicopters
Bart101 suffers from a medical condition called "Compulsive Inpulsive HeliAddict"
X3
gashead (05-02-2011)
Hi,
I think the hard Avant O-Rings are around 90 Duometer and the softer Avant O-Rings are around 70 Durometer but I'm not 100%. I think the old standard setup for the Aurora is one soft and one hard O-Ring per side. The newer type uses a one piece plastic unit with an O-Ring.
You can use any dampener designed for an 8mm spindle, I know a few people who have used the MA O-Ring and the newer one piece designs. I myself use the HyperRings, originally designed for the Synergy N9.
Check out these dampeners from Miniature Aircraft:
Fast Lad Performance
Thanks!
Rossco
Synergy N5C / Synergy E7 / Synergy E5
Synergy R/C Helicopters / Rail Blades / / Scorpion Power Systems / Fast-Lad Performance
Equipment for Sale:
MS 710 Night Blades & Charger
Ross, I have a set of HyperRings here that only have around 5 flights on them. They are yours if you send me an address.
They are softer than the now standard hybrid dampers. The old O ring dampers were designed to be used with the grooved spindle. I wouldn't reccomend using them.
The new hybrid dampers capture the inner race of the inside main grip bearing so you may need to use a thin shim with the HyperRings to ensure bearing capture.
Member of Byley Model Flying Club
gashead (05-02-2011)
What thickness shim is needed Tom? any ideas?
James
Sponsored by
Align-Trex.co.uk
Optifuel/optipower
MKS servotech
5 Eddie gold stars and christmas star
Ive got a couple of grooved spindles you can have if you decide to go down that route
TSA infusion700 YS120
Trex 700n DFC YS120
member of :
South cheshire heliaddicts
gashead (06-02-2011)
Tom, are these hybrid dampers the semi ridged Cnc ones?Originally Posted by Tom Burgess
Ross, I have a set of HyperRings here that only have around 5 flights on them. They are yours if you send me an address.
They are softer than the now standard hybrid dampers. The old O ring dampers were designed to be used with the grooved spindle. I wouldn't reccomend using them.
The new hybrid dampers capture the inner race of the inside main grip bearing so you may need to use a thin shim with the HyperRings to ensure bearing capture.
Sent from my iPhone using Tapatalk
Thanks
Jonathan
trex 600
Trex 450 v2
and an
Hey Jon,
Yes these one's.
AVANT CNC SEMI-RIGID DAMPENER SET | Midland Helicopters Ltd
Member of Byley Model Flying Club
Posting Permissions
LinkBack URL
About LinkBacks
Reply With Quote
Bookmarks